Real Carbon Fiber Front Intake Air Blades Trim for Model 3 Highland Performance 2024+
Real Carbon Fiber Front Intake Air Blades Trim for Model 3 Highland Performance 2024+
Couldn't load pickup availability
Real Carbon Fiber Front Intake Air Blade Trims for Tesla Model 3 Highland Performance 2024+
Upgrade the front bumper of your Model 3 Highland Performance with genuine 3K dry carbon fiber air blade trims. Designed specifically around the factory Performance front-intake geometry, this left-and-right pair adds a sharper carbon-fiber appearance while following the original airflow channels.
🏁 Genuine 3K Dry Carbon Fiber
Made from authentic 3K dry carbon fiber rather than ABS plastic, printed carbon texture or vinyl wrap.
📐 Performance-Specific Fit
Designed specifically around the 2024+ Model 3 Highland Performance front bumper and intake-blade geometry.
✨ Glossy or Matte Finish
Choose a high-shine Glossy Carbon Fiber finish or a lower-reflection Matte Carbon Fiber finish to match your preferred exterior style.
🔧 3M Adhesive Installation
Installs over the factory intake-blade area using heavy-duty automotive 3M double-sided tape without drilling into the bumper.
Designed for the Highland Performance Front Fascia
Real Carbon Fiber Exterior Upgrade
The exposed carbon weave provides a genuine carbon-fiber appearance instead of an imitation printed pattern.
Left + Right Symmetrical Pair
The package includes matching pieces for both sides of the front intake area.
Follows the Factory Intake Shape
The trims are designed around the original Performance bumper contours to maintain a clean visual transition along the front fascia.
100% Authentic 3K Dry Carbon Fiber
Tesery specifies genuine 3K dry carbon fiber for this exact product. It is not listed as ABS, hydro-dipped plastic, vinyl or a carbon-fiber-pattern overlay.
Carbon Construction Details
The exact page confirms 3K dry carbon fiber but does not publish laminate thickness, fiber orientation, resin specification, manufacturing pressure, autoclave cycle or finished part weight. Do not add those technical values unless separately confirmed for this exact SKU.
Vehicle Compatibility
| Vehicle | Fitment |
|---|---|
| Tesla Model 3 Highland Performance | 2024+ |
| Standard / Long Range Model 3 Highland | Not Listed for This Product |
| Model 3 2017–2023 | Not Compatible |
⚠️ Performance Version Only
This product is specifically shaped for the Model 3 Highland Performance front bumper. Do not assume fitment on a standard Highland simply because both vehicles are 2024+ Model 3 refresh models. Verify that your vehicle has the matching Performance front-intake design before ordering.
Finish Options
| Finish | Appearance |
|---|---|
| Glossy Carbon Fiber | Reflective high-shine exposed carbon-fiber finish |
| Matte Carbon Fiber | Lower-sheen exposed carbon-fiber finish |
Supplier-Designed Aerodynamic Function
Tesery states that the air blade trims are designed to guide airflow along the front-intake area and reduce front-end turbulence. Their shape follows the factory Performance intake channels rather than acting as a purely flat decorative overlay.
⚠️ No Published Aerodynamic Test Data
The supplier describes aerodynamic benefits, but the current page does not publish CFD results, wind-tunnel testing, drag-coefficient changes, downforce values or independently verified high-speed performance data. Do not advertise a specific performance gain.
Designed Around Factory Openings & Sensors
Tesery states that the trims were designed from original vehicle geometry to follow the front bumper channels without blocking the intended airflow path.
The supplier also states that the installed trims are designed not to interfere with the applicable front parking / driver-assistance sensor areas.
⚠️ Verify Clearance After Installation
After installation, visually confirm that the trim does not cover any camera, sensor, vent opening or moving component on your specific vehicle. Remove or reposition the part if alignment is incorrect.
3M Adhesive Installation
1. Clean the Installation Area
Remove dust, wax, grease and road residue from the factory front-intake surfaces.
2. Dry the Surface Completely
Adhesive bonds best to a clean and fully dry installation surface.
3. Dry-Fit Both Trims
Position the left and right pieces without adhesive first and verify their alignment with the bumper contours.
4. Use the Adhesion Promoter
Apply the supplied promoter pads according to the product instructions in the intended adhesive contact areas.
5. Apply the 3M Tape
Use the supplied automotive 3M double-sided tape as intended on the rear mounting surfaces.
6. Align & Press Into Position
Carefully align each carbon-fiber trim and apply firm, even pressure across the adhesive contact areas.
7. Check All Edges
Confirm that every edge remains fully seated and that no portion lifts away from the bumper.
⚠️ Dry-Fit Before Applying Adhesive
Do not permanently attach the trims until both pieces have been test-fitted and the correct Performance bumper shape has been confirmed. Repeated removal and reapplication can reduce adhesive effectiveness.
Removal Guidance
Tesery recommends using mild heat from a hair dryer to soften the adhesive during removal, followed by isopropyl alcohol or a suitable automotive adhesive-residue remover if residue remains.
Paint-Surface Removal Note
The supplier states that the adhesive can be removed safely using mild heat and proper cleaning techniques. Actual removal results can depend on paint condition, temperature, installation duration and prior refinishing, so remove the trims slowly and carefully.
Cleaning & Care
Routine Cleaning
Use automotive-safe soap, water and a clean microfiber cloth.
Avoid Abrasives
Do not use abrasive pads, aggressive polishing compounds or sharp cleaning tools.
Inspect the Adhesive Edges
Periodically check the perimeter for lifting, especially after high-pressure washing or extreme weather.
Remove If Loose
Do not continue driving with a trim piece that is visibly loose or partially detached.
Avoid Direct High-Pressure Spray at the Edges
High-pressure water directed closely at an adhesive edge can place additional stress on the bond. Keep pressure-washer nozzles at a reasonable distance and avoid concentrating the spray directly under the trim edges.
Specifications
| Attribute | Details |
|---|---|
| Product Type | Front Intake Air Blade Trim Pair |
| Vehicle | Tesla Model 3 Highland Performance |
| Model Year | 2024+ |
| Material | 100% Authentic 3K Dry Carbon Fiber |
| Finish Options | Glossy Carbon Fiber / Matte Carbon Fiber |
| Quantity | 2 PCS – Left + Right |
| Installation | Heavy-Duty Automotive 3M Double-Sided Tape |
| Drilling | Not Specified as Required |
⚠️ Unpublished Specifications
The current exact page does not publish individual trim dimensions, total installed weight, carbon laminate thickness, aerodynamic drag change, downforce value, wind-tunnel results or independently verified performance data. Do not add those values unless separately confirmed for this exact product.
Package Includes
1 × Left Front Intake Air Blade Trim
1 × Right Front Intake Air Blade Trim
1 × Roll of Automotive 3M Double-Sided Tape
2 × Adhesion Promoter Wipe Pads
Quick Answers
Is this real carbon fiber?
Yes. Tesery specifies 100% authentic 3K dry carbon fiber for this exact product.
Does it fit every Model 3 Highland?
No. The exact product page identifies this version specifically for the Model 3 Highland Performance 2024+.
Does it fit the 2017–2023 Model 3?
No. The previous-generation Model 3 uses a different front bumper design.
Which finishes are available?
Current options are Glossy Carbon Fiber and Matte Carbon Fiber.
How many pieces are included?
The set includes two carbon-fiber trims: one left-side piece and one right-side piece.
How are they installed?
The supplier specifies direct stick-on installation using heavy-duty automotive 3M double-sided tape.
Are adhesion promoter pads included?
Yes. The current package contents list two adhesion promoter wipe pads.
Will the trims block the front air intake?
Tesery states that they are designed around the factory intake channels so they do not block the intended airflow path when correctly installed.
Do they improve aerodynamics?
The supplier states that the shape is intended to refine airflow around the front intake area. No independent CFD, wind-tunnel or quantified aerodynamic test results are published on the current product page.
Can they be removed later?
Yes. Tesery recommends mild heat to soften the adhesive, followed by a suitable adhesive-residue cleaner if necessary.
Share
